Is it possible to drive a car with a blocked heater core?

 Although you may be able to drive with a blocked heater core, do not do so since it might cause engine overheating and damaged engine components. A blocked heater core might restrict coolant circulation, causing the engine to overheat.

In any case, keep an eye on the temperature monitor if you decide to drive with a blocked heater core.

You can also choose to skip the heater core but be sure to research the consequences of doing so beforehand.

What Causes a Clogged or Faulty Heater Core?

A blocked heater core can be caused by a number of factors. While their causes may differ, they all point to the same problem, which must be resolved in order for the heater core to function properly again.

Check MOT history with car servicing and repair garage to make sure you have enough time to get this problem rectified. The justification for this is that if a driver's sight is poor, it might result in an MOT test failure.

The following are some of the most typical reasons for a faulty heater core:

1.     Scale/Rust build-up

Corrosion and rust cause the cooling system to lose efficiency. In any event, if there is scale/rust build-up within the system unit, heater exchangers suffer more and the heater core is no exception. The use of coolant in the radiator for an extended period of time causes rust to form.

2.     Faulty thermostat

A defective thermostat may not choke the heater core, but it will prevent warm air from being released. When you start a car, the thermostat stays closed until the engine reaches a comfortable operating temperature. The thermostat opens as the engine heats up, allowing cold coolant from the radiator to circulate to the engine and the heater core. If you don't have a thermostat or it's jammed open, the engine won't be able to reach a safe operating temperature. In place of warm air, the heater will put in the lukewarm or chilly air.

3.     Coolant/oil mixing

When oil and coolant combine, sludge, sometimes known as rust, forms in the cooling system. The coolant circulates the sludge to different sections of the cooling system components, including the heater core, as it travels via the coolant hoses and pipes. As the circulation continues, system components will get clogged. This obstructs or slows coolant flow via the heater core.

The most prevalent cause of oil in coolant and coolant in the oil is as follows.

Using leak-stopping products - There are a variety of coolant leak stopper products on the market that claim to remedy coolant leaks without the need to raise a finger. These products, of course, deliver on their promises, but they also have side effects. These substances can block the cooling system's components. Furthermore, the heater core has no control over it. When you use more than the suggested amount, this happens. It can also block the radiator.

Is it possible for a blocked heater core to cause overheating?

According to reports, a blocked heater core might cause engine overheating. Did you get what I meant about a little proclivity? This implies that, in most circumstances, it will not cause engine overheating, but it may impair the cooling system in other cases. When your engine overheats, you should investigate a number of additional variables. It's preferable to flush the heater core if you have a blocked heater core and your engine temperature is running high.

As a result of this, your vehicle could possibly fail the next MOT test, so it is recommended to check MOT status of your vehicle and fix this issue as soon as possible. If you want to dig a bit deeper, you can complete an MOT history check online to see if the heater core was a reason for failure in the past.

To do this you may need to refer to the work completed with each MOT failure in the past which is connected to an overheating issue or due to visibility for driver issue.

Is it possible to clear the heater core with a radiator flush?

The radiator and the heater core are two separate components with comparable but distinct functions. Yes, they're both parts of a cooling system, and the same coolant runs through both.

Flushing a radiator can help prevent rust from forming in the heater core. Flushing a heater core with a garden hose is the most efficient technique to unclog it.